Shop by Brand: PAC

PAC 1998-2013 Harley Davidson splash cover & mounting hardware
Includes two mainframes (one with hinged cover)
Installs one single radio
Instructions & Hardware included

4 OHM 0-800
8 OHM 0-400
WORKS WELL W/ 5.25 SIZE SPEAKERS

4 OHM 0-600
8 OHM 0-300
WORKS WELL W/ 6"e; SIZE SPEAKERS

This only extends range of a remote eye, It does not extend the range
of IR wireless headphones.
17' EXTENDER - CARRIES THE SIGNAL FROM IR REMOTE CONTROLS TO DEVICES
THAT ARE HIDDEN OR OUT OF RANGE OF THE REMOTE CONTROL.
40-56 KHz CARRIER FREQUENCY RANGE.
IR RECEIVER, 17' CABLE, + IR REPEATER - CONTROLS MORE THAN 1 DEVICE IF
THEY ARE LOCATED WITHIN LINE-OF-SIGHT RANGE OF THE IR REPEATER.

Provides an audio/video signal output from the factory radio in select 2012-Up GM Vehicles to an aftermarket monitor.
Also for use with a radio replacement interface (i.e. RP5-GM32) to replace a factory radio and retain the overhead LCD monitor and IR system.

GMRVD2 APPLICATIONS:
Option A) Can be used with RP5-GM32 radio replacement interface to install an aftermarket radio and route the A/V signal to the OEM rear monitor.
The GMRVD2 can also pass A/V from the vehicle's rear A/V input, into the new aftermarket radio. From there, the cable routes the signal to the OEM rear monitor, and IR transmitter in the OEM RSE.
Option B) Can be used to add aftermarket video screen(s) to the vehicle and route video from the OEM radio, or DVD player in center console to the new monitor(s).
Compatibility and Notes: (Please read before purchasing this part)
1. When replacing factory radio the GMRVD2 must be used in conjunction with the OS-4 or RP5-GM33 to retain all safety and convenience systems.
2. PAC 0S-4/RP5-GM32 is needed to power the IR headphone system.
3. Click for INSTALLATION INSTRUCTIONS

The GMRVD2 must be used in conjunction with PAC OS-4 or RP5-GM32 to retain all safety and convenience systems.

Adjustable High Power 2 channel Line Out Converter
Handles input signals up to 50 Watts per channel
50 watts max power handling
Linear 20 to 20,000Hz output based on input signal
Transformer isolated for optimal sound and performance
Maintains correct phasing
Works with most factory installed radios
Detachable wiring harness
Integrated wire tie mounts

LINEAR FROM 20-20,000 Hz @ +/-0.5dB (SIGNALS BELOW 20 Hz ARE CUT OFF).
MAINTAINS SIGNAL PHASE
ISOLATED INPUT + OUTPUT CIRCUITS TO PREVENT GROUND LOOP NOISE.

OEM-1 with a vehicle specific harness plugs into the vehicle's wiring and provides a stereo RCA audio output for adding aftermarket amplification.
Provides full range audio output 20-20,000Hz. Audio output level is controlled by the volume of the factory radio.

Compatibility Notes
Warning chimes will sound through the front left RCA output
Not compatible with factory amplified audio systems
Turning on the rear seat entertainment controls will make the rear outputs of the interface play the second audio source

Plug in installation retains factory wiring integrity
Linear 20-20,000Hz sound reproduction based on input signal
4 channel RCA output
Output level controlled by factory radio

Connects virtually any audio source.
» Dash mountable aux input adapter provides factory look and finish.
» 3.5mm to RCA adapter included.
» Extends aux input
» "e;AUDIO INPUT"e; label on dash mounted connector.

Package Contents :
» 3.5mm (male) to 3.5mm (female) dash panel mount audio input (6ft) x1
» 3.5mm (male) to 3.5mm (male) Audio cable (4ft) x1
» 3.5mm (female) to RCA Adapter Cable (6 inches) x1

PAC Harness for Toyota & Scion 2014-16 to add a Back up Camera with Factory Radio.
The harness simply plugs into the factory harness and provides the video from the back-up camera for aftermarket radio installations or connects between the factory harness and factory radio for integration of an aftermarket back-up camera.

Product Features

Dual function item
Retains OE back-up camera for radio replacement applications
Allows addition of an aftermarket back-up camera to factory systems
Prewired 6 volt output wire for OE camera retention when used with PAC RP4.2-TY11 radio replacement interface
Integrated 6 volt output wire can be used for powering an aftermarket back-up camera (6V models only) when adding camera feature to OE radio

ALL-IN-ONE RADIO REPLACEMENT & STEERING WHEEL CONTROL INTERFACE
PRE-LOADED WITH AMPLIFIER RETENTION & NAVIGATION BASED OUTPUT SIGNALS
RETAINS ALL IMPORTANT OEM SAFETY & CONVENIENCE FEATURES
DATA-CONTROLLED RAP ACCESSORY OUTPUT
DATA-CONTROLLED OUTPUTS

Bluetooth audio receiver to transmit music from a phone to any car, boat, or motorcycle with an AUX input or direct to amplifier.
4V output and weather-proof for all your adventures on the road, off road or on the water!
Bluetooth receiver featuring a weather-proof housing
Male 3.5mm to female RCA Converter
3pc weather proofing heat shrink
Coated PCB boards
Fully sealer housing for weather proofing
Small enough to be installed in limited space
4V RCA Output
Easy two wire installation

USE- TO ADD AN AMPLIFIER TO A FACTORY RADIO W/O RCA OUTPUT.
SNI8, 15 + 35 ALL:
-ARE LINIAR FOR 20 - 20,000HZ
-FEATURE TRANSFORMER ISOLATION BETWEEN INPUTS AND OUTPUTS
-KEEP THE SIGNAL PHASE
SNI-35 CONVERTS FROM 2-40 WATTS/CHANNEL - ADJUSTABLE CONVERSION
SNI-15 "e; "e; 2-30 "e; "e; - FIXED 10:1 CONVERSION
SNI-8 "e; "e; 2-10 "e; "e; "e; 5:1 "e;

PRO Series 2-Channel High Power Line Output Converter
Designed to optimize audio levels between radio and amplifier to achieve the best audio quality
Ideal for use when adding an amplifier to an OEM system
Speaker level input to RCA level output
Single dial, precision matched stereo, level gain adjustment
Ultra-compact size for greater installation flexibility

*Replaces SOEMT*
Level 7 adds Remote turn on and precision SMT contruction over levels 3 and 5.

PRO Series 2-Channel High Power Line Output Converter
Designed to optimize audio levels between radio and amplifier to achieve the best audio quality
Ideal use when replacing factory (OEM) radio or amplifier
Configurable for speaker level or RCA level input/output
Single dial, precision matched stereo, level gain adjustment
Signal-sensing circuit for amplifier remote turn-on
Surface Mount Construction (SMT) for reliable and noise-free operation
Ultra-compact size for greater installation flexibility

Level 7 adds Remote turn on and precision SMT contruction over levels 3 and 5.

PRO Series 4-Channel High Power Line Output Converter
Designed to optimize audio levels between radio and amplifier to achieve the best audio quality
Ideal use when replacing factory (OEM) radio or amplifier
Configurable for speaker level or RCA level input/output
Single dial, precision matched stereo, level gain adjustment
Signal-sensing circuit for amplifier remote turn-on
Surface Mount Construction (SMT) for reliable and noise-free operation
Ultra-compact size for greater installation flexibility

NOISE FILTER PAC 12 AMP

ALLOWS REPLACEMENT OF FACTORY RADIO W/AFTERMARKET RADIO WHILE
RETAINING ONSTAR + OTHER FUNCTIONS - SEE www.pac-audio.com

2004 - 2007 CHEVY MALIBU
2005 - 2006 CHEVY COBALT
2005 - 2007 PONTIAC G6

Retains OnStar® when the factory radio is replaced
Retains Factory Bluetooth (2009+ model vehicles)
Retains rear seat audio controls
Retains all warning chimes (chime module included)
Retains back-up sensors/park assist
Retains factory BOSE audio systems
Retains factory premium BOSE audio (does not support fading)
Supports non-amplified audio systems
Built in pre-programmed SWC retention
Dual zone function
Chime volume adjustment (factory buttons)
Rear Seat Entertainment Retention
OnStar volume adjustment
Retained accessory power output (R.A.P.)
Reverse Wire output
VSS (Vehicle Speed Sense) output
Illumination output
Parking brake output
Includes antenna adaptor
Retains OnStar Turn-By-Turn voice prompts

Radio Replacement interface with OnStar retention for select 29-bit GM LAN vehicles with or without BOSE sound system
In-field updateable firmware via USB (using PAC-UP)
Retains OnStar® when the factory radio is replaced
Retains Factory Bluetooth (2009+ model vehicles)
Retains rear seat audio controls
Retains factory XM
Retains all warning chimes (chime module included)
Retains back-up sensors/park assist
Retains back-up camera signal
Retains factory BOSE audio systems
Retains factory premium BOSE audio (Y91 digital. does not support fading)
Supports non-amplified audio systems
Steering wheel control harness (pre-wired)
Dual zone function
Chime volume adjustment (factory buttons)
OnStar volume adjustment
Retained accessory power output (R.A.P.)
Reverse Wire output
VSS (Vehicle Speed Sense) output
Illumination output
Parking brake output

Included:
(1) OS-5 module
(1) Vehicle wiring harness
(1) Chime module
(1) Antenna adaptor
(1) Instruction manual

RadioPro Radio Replacement Interface With Built In OnStar Retention, Pre-Programmed Steering Wheel Control Retention and Navigation Outputs
Only compatible with 1500 series trucks. 2500 & 3500 series trucks must use the RP5-GM31
Does not retain Bose amplifier. Information on how to bypass the factory amp is included in the instructions
Retains OnStar Telematics system
Retains front and rear park assist
Data controlled outputs for connection to your navigation radio; speed, reverse and E-brake status output wires
Retains original steering wheel control functions with the new radio with no additional interface or programming needed
Data controlled RAP accessory output
Works right out of the box with most radio brands
Keeps vehicle data-bus intact for service
Interface can be quickly updated if needed from the PAC website using a PAC-UP USB adapter

Make Model Year Category Product
Chevrolet Silverado 2014 Radio Replacement RP5-GM51
GMC Sierra 2014 Radio Replacement RP5-GM51

Radio Replacement Interface With Built In OnStar Retention, Pre-Programmed Steering Wheel Control Retention and Navigation Outputs

Compatibility Notes
2012+ GM trucks and SUVs equipped with factory navigation radios require the RP5-GM32
In Premium Amplified Systems there will be no fading capability of the aftermarket stereo.
Chevrolet Express vans & GMC Savannah vans equipped with diesel engines are not compatible
In order to retain the factory XM tuner the aftermarket head unit MUST be equipped with an auxiliary input
In order to retain the factory XM tuner the vehicle must be equipped with steering wheel controls and a driver information center

Product Features

Retains OnStar® when the factory radio is replaced
Retains Factory Bluetooth (2009+ model vehicles)
Retains rear seat audio controls
Retains factory XM
XM Text displayed in the Driver Information Center (cluster display)
Retains all warning chimes (chime module included)
Retains back-up sensors/park assist
Retains back-up camera signal
Retains factory BOSE audio systems
Retains factory premium BOSE audio (Y91 digital. does not support fading)
Supports non-amplified audio systems
Built in pre-programmed SWC retention
Dual zone function
Chime volume adjustment (factory buttons)
Rear seat audio and video (GMRVD) required
OnStar volume adjustment
Retained accessory power output (R.A.P.)
Reverse Wire output
VSS (Vehicle Speed Sense) output
Illumination output
Parking brake output
Includes antenna adaptor
Retains lane departure warning system
Retains OnStar Turn-By-Turn voice prompts
In package updatable using the PAC-UP

Pioneer Alpine & Kenwood Video Bypass
Universal Trigger Output Module
Low Voltage Trigger
Latch and Unlatch Output From a Pulsed Unit
Double Pulse Output

RADIO REPLACEMENT INTERFACE FOR 2005 AND UP CHRYSLER/DODGE/JEEP LSFT CANBUS EQUIPPED VEHICLES.
INTERFACE FOR INSTALLATION OF NAVIGATION OR RADIOS INTO VEHICLES
FACTORY AMPLIFIER TURN-ON
STEERING WHEEL CONTROLS CAN BE RETAINED USING THE SWICAN AND A RADIO SPECIFIC SWI-INTERFACE.

Radio Replacement Interface for GM Vehicles with Class II databus and 24-pin harness.

Product Features

High current 10A accessory output
Data controlled outputs for connection to your navigation radio; speed, reverse and E-brake status output wires
Retains factory installed amplifier (if equipped)
Data controlled RAP accessory output
Keeps vehicle data-bus intact for service
Plug-in-connection for steering wheel control module (SWI-RC or SWI-X)
In package updatable using the PAC-UP
Adjustable chime volume: 4 levels, and off